AV Products C4 Manuel d'utilisateur télécharger pdf

INTRODUCTION

The Digicom AV and the Digicom AV+ are BABT approved communication units, which

transfer alarm information to a Central Station via the public telephone network.

Digicom AV/AV+ features include:-

Supports Audio Verification when used in conjunction with the AV microphone and

AV speaker units.

Completely programmable using a standard (tone dial) telephone.

Led indication of an alarm communication.

4 programmable input channels.

1 programmable output.

Fully programmable reporting map.

2 Primary & 1 Auxiliary telephone numbers (up to 24 digits each).

Supports both Loop Disconnect and Tone (DTMF) dialling.

Separate Primary & Auxiliary account codes (up to 8 digits each).

Automatic timed check call facility (between 1 and 99 days).

Automatic answer facility.

Controllable via a 1200 baud 3 wire serial link.

Programmable line monitoring facility.

Test call facility.

Digicom AV+ extra feature:-

BT Network Services compatable and therefore can be installed on a non dedicated line,

without compromising the alarm systems integrity.

DIGICOM AV/AV+

TECHNICAL MANUAL

Fig 1 Digicom AV/AV+ Layout (with lid removed)

PROGRAMMING PHONE SOCKET

CABLE STRAIN

RELIEF

PHONE LINE

TERMINALS

CABLE STRAIN

RELIEF

CABLE STRAIN

RELIEF

CONTROL

EQUIPMENT

TERMINALS

MOUNTING

HOLES

D051-2

LED

TNV

SELV

Fig 4 DIGICOM AV/AV+ PROGRAMMING DETAILS

PROGRAMMING CODES

PRIMARY TEL No. 1

PRIMARY TEL No. 2

AUXILIARY TEL No.

PRIMARY ACCOUNT CODE

AUXILIARY ACCOUNT CODE

15 CHECK CALL TIME (DAYS) limits 00 - 99

16 No. OF CALL ATTEMPTS limits 1 - 8

17 No. OF CALLS BEFORE limits 1 - 8

FAILURE TO COM.

18 PRIMARY 1 TEST CALL

19 PRIMARY 2 TEST CALL

20 AUXILIARY TEST CALL

21 TEST MIC

22 TEST SPEAKER

23 TEST MIC MULTIPLEXER

C1 C2 C3 C4

09 CHANNEL TYPES

0 - ALARM

1 - RESTORE

2 - SET/UNSET

C1 C2 C3 C4

10 CHAN. POLARITIES

0 - POS START

1 - NEG START

11 LINE MONITOR

0 - OFF

1 - LINE CUT

2 - FULL

C1 C2 C3 C4 CHK

07 REPORTING MAP

0 - OFF (disabled)

1 - PRI

2 - AUX

3 - PRI & AUX

4 - AV

08 AV OPTIONS

0 - AV PRI

1 - PRI & AV AUX

2 - PRI CALL BACK

3 - CALL BACK ONLY

12.

LOW

BATT.

13 OUTPUT MODE (O1)

0 - FAULT MONITOR

1 - COMMUNICATION SUCCESSFUL

2 - AV AUX OUTPUT

1 2 3 4 5 6

Résumé du contenu

Page 1 - TECHNICAL MANUAL

INTRODUCTION The Digicom AV and the Digicom AV+ are BABT approved communication units, which transfer alarm information to a Central Station via the p

Page 2 - DIGICOM AV+ DIGICOM AV

2. INSTALLATION Fixing Details The Digicom AV/AV+ is a host independent unit and therefore can be mounted inside any standard alarm control panel usin

Page 3 - ADDRESS

Channel Inputs (C1-C4) Connect the appropriate outputs from the Control Panel to these inputs. These inputs are programmable, making them compatable w

Page 4

Fig 3 Programming sequence * x x x x x x x x x x # # PROGRAMMING DETAILS The Digicom AV/AV+ has an on board memory d

Page 5

8. Restore Defaults (code 00) Connect the terminals marked RX and TX together using a link wire and enter programming code 00, the program successful

Page 6

Auxiliary Telephone Number (code 03) The Digicom can also be programmed with one auxiliary number (up to 24 digits). This is programmed in the same wa

Commentaires sur ces manuels

Pas de commentaire

AV Products C4 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Haut-parleurs de la barre de son AV Products C4. digicom av/av+ technical manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Haut-parleurs de la barre de son AV Products C4